How much does a made-to-measure shower tray cost?
There is no price list, because no two bathrooms are the same. Yours depends on five things: the size of the opening (width matters more than length), the thickness you choose — 20 or 30 mm —, the colour, how many edges are exposed (a tray boxed in by three walls is not the same work as one with two visible sides) and whatever extras your installation calls for, which we explain in detail when we talk. Send us the size of the opening and we will give you a fixed price within 24 working hours. If you have already taken the measurements, no site visit is needed.
Is micro-marble better than resin?
It helps to know that micro-marble also contains resin: both are the same family of material. The difference is the proportion of mineral, and therefore the weight and rigidity. Our micro-marble has a density of 2,400 to 2,500 kg/m³, about 73 kg/m² at 30 mm, against the 30-40 kg/m² of a standard resin tray. On top of that, the anti-slip on a gel-coated tray lives in a surface layer a few tenths of a millimetre thick; ours is bush-hammered into the material itself, which is homogeneous and waterproof right through. If you are comparing quotes, always ask for the weight per square metre.
Do you make small or unusual sizes?
Yes, and that is exactly the point of making them to measure. We work with widths from 60 to 100 cm and lengths from 60 to 250 cm, cut to the exact size of the opening. If your bathroom needs 87 cm because that is where the bath was, the tray is 87 cm: no need to build up the floor or settle for the nearest standard size. Small openings in flats and long, narrow shower runs are what we make most.
20 or 30 mm? Which one do I need?
It is not only about rigidity, and there are three things worth knowing before you decide. First: not every colour is available in both thicknesses. If you are set on a colour, that may fix the thickness for you; if you are set on the thickness, the colour range narrows. Tell us which of the two matters more and we start from there. Second is the weight, which follows the size: a 90×140 tray in 30 mm comes to around 93 kg, and the same one in 20 mm to about 62. Carrying 93 kg up a staircase, through a door opening or around a corridor is not always feasible, so on large sizes the thickness ends up being decided by access to the site. And third: the 30 mm allows a steeper fall to the waste, because there is more material to work the slope into. In exchange, the 20 mm is the one for refurbishments without building work — it beds over the existing floor or the old tray, gains very little height and avoids the rubble. Send us the size of the opening and tell us about the access, and we will tell you which one fits.
Do you prepare it for the shower screen?
Yes. We need to know which screen you are fitting and how it sits — on the tray, outside it, with a profile or into a recess — because that affects the edge, the usable width and sometimes the setting-out. If you have not chosen it yet, tell us anyway: we make the tray so that it takes the most common solutions and does not rule any of them out.
Do you fit it yourselves?
No. We are fabricators: we deliver the tray finished and your builder or plumber installs it. What we do is leave them nothing to sort out, because the tray leaves the workshop at the exact size and needs no adjusting on site. And we give them the one instruction that really matters: the base must be flat and the tray bedded across its whole surface, not just around the edges. That is where almost every later problem starts.
Are they anti-slip?
Yes. The bush-hammered finish is a texture mechanically worked into the micro-marble itself, not a layer applied on top. That means the same material continues below the surface, and the texture cannot wear away until the tray is smooth. Spain has no specific slip-resistance standard for shower trays — the building code classifies floors, not trays — so be wary of anyone quoting you a class without showing the test report.
Does the water drain well? Can it pool?
It drains properly, but it is worth knowing what to expect: a made-to-measure tray does not clear water like a pool channel, for three reasons. The first is the fall, which depends on the thickness and the size: the larger the tray and the thinner it is, the gentler the slope to the waste necessarily becomes. The second is the bush-hammering itself: the texture that gives you grip is what slows the water, because a textured surface does not shed like a smooth one. It is a deliberate trade-off, and we would rather you had a safe footing. And the third is not down to us: real drainage is set by the installation — the diameter and fall of the waste pipe, the trap and whether there is a bottle trap. A well-made tray over a badly resolved waste will still drain badly, so it is worth having your plumber take care of that part.
What maintenance does it need?
Very little: water and a neutral soap for everyday cleaning. Being a compact, homogeneous material, it does not absorb. What you should avoid are strongly acidic products and metal scourers, just as with any stone worktop. We have a maintenance page with specific recommendations by material.
How do I request a quote?
Via WhatsApp or from the contact page, giving the width and length of the shower opening. You can attach a photo of the bathroom to the form itself: one photo saves two or three emails back and forth and lets us see the waste, the walls and how the screen fits. We reply within 24 working hours.